CCNA - SRWE - 15.6.4

A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226. What is the purpose of this command?

• to add a dynamic route for the destination network 0.0.0.0 to the routing table

• to fordward packets destined for the network 0.0.0.0 to the device with IP address 209.165.200.226

• to provide a route to forward packets for which there is no route in the routing table

• to forward all packets to the device with IP address 209.165.200.226

Which type of static route that is configured on a router uses only the exit interface?

• recursive static route

• fully specified static route

• directly connected static route

• default static route

A network administrator uses the command ip route 172.18.0.0 255.255.0.0 S0/0/1 to configure a floating static route on a router. That route will function as a backup route to reach the EIGRP learned network 172.18.0.0/16. After this configuration, the EIGRP route is removed from the routing table even though EIGRP is still functioning properly. Why is the static route not functioning as intended?

• The administrative distance value is not high enough on the static route

• The network mask is incorrectly configured

• The destination network is incorrrectly configured

• The next hop neighbor IP address is not configured.

What type of static route is created when the next-hop IP address and exit interface are specified?

• directly connected static route

• floating static route

• recursive static route

• fully specified static route

What is the correct syntax of a floating static route?

• ip route 172.16.0.0 255.248.0.0 10.0.0.1

• ip route 0.0.0.0 0.0.0.0 serial 0/0/0

• ip route 209.165.200.228 255.255.255.248 serial 0/0/0

• ip route 209.165.200.228 255.255.255.248 10.0.0.1 120

Which static route statement shows a recursive IPv6 static route?

• ipv6 route 2001:db8:cafe:1::/56 S0/0/0

• ipv6 route 0::/0 S0/0/0

• ipv6 route 2001:db8:cafe:1::/56 2001:db8:1000:10::1

• ipv6 route 0::/0 S0/0/0 254

• ipv6 route 2001:db8:cafe:1::/56 S0/0/0 2001:db8:1000:10::1

A network administrator is configuring a route to forward packets to a specific web server. What type of route should be configured by the administrator?

• an OSPF route

• a static route with an administrative distance higher than 1

• a default route

• a host route

• an EIGRP route

Which command would create a valid IPv6 default route?

• ipv6 route ::/0 2001:db8:acad:2::a

• ipv6 route 2001:db8:acad:1::/64 ::1

• ipv6 route ::/0 fe80::1

• ipv6 route ::/128 2001:db8:acad:1::1

What is a characteristic of a default static route? ​

• It backs up a route already discovered by a dynamic routing protocol

• It uses a single network address to send multiple static routes to one destination address.

• It is configured with a higher administrative distance than is the original dynamic routing protocol.

• It identifies the gateway IP address to which the router sends all IP packets for which it does not have a learned or static route.

What is the purpose of a floating static route?

• It allows connectiviy to remote destinations that are not contained in the routing table.

• It is commonly used when a dynamic routing protocol is not being used.

• It allows an alternate connection to be used when the preferred link fails.

• It allows summarization of contiguous networks.