QUIZ for The Anesthesia Machine 2024

QUIZ for The Anesthesia Machine 2024

Professional Development

10 Qs

quiz-placeholder

Similar activities

mcq 21/01/23

mcq 21/01/23

Professional Development

12 Qs

Day 2 ICU Lecture

Day 2 ICU Lecture

Professional Development

15 Qs

post max anesthesia

post max anesthesia

Professional Development

10 Qs

VOICE

VOICE

Professional Development

10 Qs

The Traphouse Quiz

The Traphouse Quiz

9th Grade - Professional Development

10 Qs

Economie - Chapitre 8 : Les transformations du commerce mondial

Economie - Chapitre 8 : Les transformations du commerce mondial

Professional Development

11 Qs

L'intelligence artificielle

L'intelligence artificielle

Professional Development

11 Qs

post test physics part 2

post test physics part 2

Professional Development

10 Qs

QUIZ for The Anesthesia Machine 2024

QUIZ for The Anesthesia Machine 2024

Assessment

Quiz

Education

Professional Development

Medium

Created by

Glenn Tan

Used 3+ times

FREE Resource

10 questions

Show all answers

1.

MULTIPLE CHOICE QUESTION

2 mins • 1 pt

All of the following are required by the 2008 ASA Guidelines for Checkout Procedures prior to Anesthesia Delivery to be performed before the start of each case, EXCEPT:

Verify patient suction is adequate to clear the airway.

Verify that pressure is adequate on the spare oxygen cylinder mounted on the anesthesia machine.

Verify that vaporizers are adequately filled and, if applicable, that the filler ports are tightly closed.

Verify that gas flows properly through the breathing circuit during both inspiration and exhalation

2.

MULTIPLE CHOICE QUESTION

2 mins • 1 pt

Graduations of a flowmeter assembly using a ball bobbin is correctly read by reading:

Through the center of the ball.

Through the top of the ball.

Through the bottom of the ball.

Through the lower menisci.

3.

MULTIPLE CHOICE QUESTION

2 mins • 1 pt

Which of following is a reasonable maneuver in order to check if the plumb-bobbin of the flowmeter is NOT stuck?

Turning the flowmeter on and see if the bobbin rotates.

Turning the flowmeter off then press the O2 flush to see if the bobbins would go up.

Turning the flowmeter on then press the O2 flush to see if the bobbins would go down.

Turning the anesthesia machine on to see if all bobbins would move.

4.

MULTIPLE CHOICE QUESTION

10 mins • 1 pt

Suppose you were doing a case under general anesthesia.  Suddenly, all the lights went out because of a power failure.  You immediately increase the O2 flow from 2 LPMs without looking at the flowmeter.  However, you inadvertently turned the N2O knob of the flowmeter up to 9LPMs instead.  Assuming that the proportioning system is intact, how much O2 will be flowing?

3 LPMs

4 LPMs

5 LPMs

6 LPMs

5.

MULTIPLE CHOICE QUESTION

2 mins • 1 pt

An E-cylinder for oxygen would have holes for pins on which of the following positions?

1, 6

2, 5

2, 4

3, 5

6.

MULTIPLE CHOICE QUESTION

2 mins • 1 pt

Media Image

The structure being pointed by the large arrow is called the:

APL valve

Pressure transducer valve

Solenoid valve

Fresh gas decoupling valve

7.

MULTIPLE CHOICE QUESTION

2 mins • 1 pt

Media Image

This diagram is typical of: 

Datex-Ohmeda 7000

Mindray Workstation A7

Drager AV-E

Drager Fabius OS

Create a free account and access millions of resources

Create resources
Host any resource
Get auto-graded reports
or continue with
Microsoft
Apple
Others
By signing up, you agree to our Terms of Service & Privacy Policy
Already have an account?