Which routing table principle is not correct?

Routing information about a path from one network to another also provides routing information about the reverse, or return, path.

Every router makes its decision alone, based on the information it has in its own routing table.

The fact that one router has certain information in its routing table does not mean that other routers have the same information.

Which route entry would be used for a packet with a destination IP address that matches an IP address of one of the router interfaces?

depends on the source of the route

A network administrator configures a static route for the same destination network that was learned automatically by the router using OSPF. Which route will be installed and why?

Static route because it has a lower administrative distance

Static route because it has a lower metric

OSPF route because it has a lower metric

OSPF route because it has a lower administrative distance

Which three advantages are provided by static routing? (Choose three.) Configuration of static routes is error-free.

The path a static route uses to send data is known.

Static routing does not advertise over the network, thus providing better security.

Static routing typically uses less network bandwidth and fewer CPU operations than dynamic routing does.

Static routes scale well as the network grows.

No intervention is required to maintain changing route information.

What are two functions of dynamic routing protocols? (Choose two.)

to avoid exposing network information

to choose the path that is specified by the administrator

What is an advantage of using dynamic routing protocols instead of static routing?

ability to actively search for new routes if the current path becomes unavailable

fewer router resource overhead requirements

more secure in controlling routing updates

What are two functions of a router? (Choose two.)

It determines the best path to send packets.

A router connects multiple IP networks.

It controls the flow of data via the use of Layer 2 addresses.

It builds a routing table based on ARP requests.

It provides segmentation at Layer 2.

When a router learns that multiple paths are available to a destination network from the same routing protocol, which factor is considered by a router to choose the best path to forward a packet?

the order of paths on the routing table

the fastest bandwidth of exiting interfaces

the reliability value of the neighboring routers

The output of the show ip route command contains the following entry: S 10.2.0.0 [1/0] via 172.16.2.2. What value is indicated by the 1 in the [1/0] portion of the output?

interface ID through which the network can be reached

What are two common types of static routes in routing tables? (Choose two)

a static route to a specific network

a static route converted from a route that is learned through a dynamic routing protocol

a static route shared between two neighboring routers

What are two reasons why an administrator might choose to use static routing rather than dynamic routing? (Choose two.)

Static routing uses less router processing and bandwidth.

Static routing is more scalable.

Static routing does not require complete knowledge of the whole network.

Static routing is easier to maintain in large networks.

Which IPv4 static route statement is true?

Using the exit interface only is common in a point-to-point configuration.

The destination network is identified using the network address and wildcard mask.

The distance keyword is used to create a fully specified static route.

The source network is identified using the network address and wildcard mask.

How is the destination network in an IPv6 static route identified?

using an IPv6 prefix and prefix length

using an IPv6 prefix and subnet mask

using an IPv6 prefix and wildcard mask

A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226 . What is the purpose of this command?

to provide a route to forward packets for which there is no route in the routing table

to add a dynamic route for the destination network 0.0.0.0 to the routing table

to forward packets destined for the network 0.0.0.0 to the device with IP address 209.165.200.226

to forward all packets to the device with IP address 209.165.200.226

Which type of static route that is configured on a router uses only the exit interface?

directly connected static route

A network administrator uses the command ip route 172.18.0.0 255.255.0.0 S0/0/1 to configure a floating static route on a router. That route will function as a backup route to reach the EIGRP learned network 172.18.0.0/16. After this configuration, the EIGRP route is removed from the routing table even though EIGRP is still functioning properly. Why is the static route not functioning as intended?

The administrative distance value is not high enough on the static route.

The destination network is incorrectly configured.

The network mask is incorrectly configured.

The next hop neighbor IP address is not configured.

What type of static route is created when the next-hop IP address and exit interface are specified?

directly connected static route

What is the correct syntax of a floating static route?

ip route 209.165.200.228 255.255.255.248 10.0.0.1 120

ip route 172.16.0.0 255.248.0.0 10.0.0.1

ip route 209.165.200.228 255.255.255.248 serial 0/0/0

ip route 0.0.0.0 0.0.0.0 serial 0/0/0

Which static route statement shows a recursive IPv6 static route?

ipv6 route 2001:db8:cafe:1::/56 2001:db8:1000:10::1

ipv6 route 2001:db8:cafe:1::/56 S0/0/0

ipv6 route 2001:db8:cafe:1::/56 S0/0/0 2001:db8:1000:10::1

A network administrator is configuring a route to forward packets to a specific web server. What type of route should be configured by the administrator?

a static route with an administrative distance higher than 1

Which command would create a valid IPv6 default route?

ipv6 route ::/0 2001:db8:acad:2::a

ipv6 route 2001:db8:acad:1::/64 ::1

ipv6 route ::/128 2001:db8:acad:1::1

What is a characteristic of a default static route?

It identifies the gateway IP address to which the router sends all IP packets for which it does not have a learned or static route.

It uses a single network address to send multiple static routes to one destination address.

It is configured with a higher administrative distance than is the original dynamic routing protocol.

It backs up a route already discovered by a dynamic routing protocol.

Which IPv6 static route would serve as a backup route to a dynamic route learned through OSPF?

Router1(config)# ipv6 route 2001:db8:acad:1::/32 2001:db8:acad:6::2 200

Router1(config)# ipv6 route 2001:db8:acad:1::/32 2001:db8:acad:6::2 100

Router1(config)# ipv6 route 2001:db8:acad:1::/32 2001:db8:acad:6::100

Router1(config)# ipv6 route 2001:db8:acad:1::/32 gigabitethernet0/0 2001:db8:acad:6::100 100

What command, or set of commands, would be used to determine if the following configuration on router HQ works as designed? ip route 0.0.0.0 0.0.0.0 serial 0/0/0 10 ip route 0.0.0.0 0.0.0.0 serial 0/1/0

HQ(config)# interface serial 0/1/0 HQ(config-if)# shutdown HQ(config-if)# end HQ# show ip route

HQ# ping 128.107.0.99 HQ# ping 64.100.0.5

Why would a floating static route be configured with an administrative distance that is higher than the administrative distance of a dynamic routing protocol that is running on the same router?

to act as a gateway of last resort

to be the priority route in the routing table

What network address and subnet mask combination would be used to create a default static route that matches any IPv4 destination?

255.255.255.255 255.255.255.255

Refer to the exhibit. What action will R3 take to forward a frame if it does not have an entry in the ARP table to resolve a destination MAC address?

sends frame to the default gateway

Which sequence correctly identifies the order of the steps that a router will perform when it receives a packet on an Ethernet interface?

The router examines the destination MAC address. The router identifies the Ethernet Type field. The router de-encapsulates the Ethernet frame. The router examines the destination IP address.

The router de-encapsulates the Ethernet frame. The router examines the destination MAC address. The router identifies the Ethernet Type field. The router examines the destination IP address.

The router examines the destination IP address. The router examines the destination MAC address. The router identifies the Ethernet Type field. The router de-encapsulates the Ethernet frame.

The router examines the destination MAC address. The router identifies the Ethernet Type field. The router examines the destination IP address. The router de-encapsulates the Ethernet frame.

The router examines the destination IP address. The router examines the destination MAC address. The router de-encapsulates the Ethernet frame. The router identifies the Ethernet Type field.

srwe

Quiz

•

Mathematics

•

12th Grade

•

Practice Problem

•

Easy

ETHAN MANAHAN

Used 5+ times

FREE Resource

164 questions

Show all answers

1.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What table does a router use to determine how to forward an IP packet?

ARP table

MAC address table

neighbor cache

routing table

2.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What action will a router take on a packet with a destination IP address that is on a remote network?

It will forward the packet directly to the device with the destination IP address of the packet.

It will forward the packet to a next-hop router.

It will forward the packet to an Ethernet switch.

It will drop the packet.

3.

MULTIPLE SELECT QUESTION

45 sec • 1 pt

Which of the following routes may be found in a routing table? (Choose all that apply.)

directly connected networks

static routes

dynamic routing protocol routes

default route

4.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is used to determine the minimum number of far-left bits that must match between the prefix in the route entry and the destination IP address.

prefix length in the routing table entry

prefix length of the destination IP address

the classful address of the network address

5.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

If a router needs to send an ARP Request for the destination IPv4 address of the packet, this means the packet will be forwarded:

To a next-hop router

To the device with the destination IPv4 address of the packet

6.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

If a router needs to send an ARP Request for the IPv4 address in one of its route entries, this means the packet will be forwarded:

To a next-hop router

To the device with the destination IPv4 address of the packet

7.

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which packet forwarding method is used by default on Cisco routers?

process switching

fast switching

Cisco Express Forwarding

Ethernet switching

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Popular Resources on Wayground

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

54 questions

Analyzing Line Graphs & Tables

Quiz

•

4th Grade

$fractions$

22 questions

fractions

Quiz

•

3rd Grade

20 questions

Main Idea and Details

Quiz

•

5th Grade

20 questions

Context Clues

Quiz

•

6th Grade

15 questions

Equivalent Fractions

Quiz

•

4th Grade

Discover more resources for Mathematics

12 questions

Add and Subtract Polynomials

Quiz

•

9th - 12th Grade

15 questions

Exponential Growth and Decay Word Problems Practice

Quiz

•

9th - 12th Grade

17 questions

Explore Experimental and Theoretical Probability

Quiz

•

7th - 12th Grade

15 questions

Parallelogram Properties

Quiz

•

10th - 12th Grade

18 questions

Solving Systems- Word Problems

Quiz

•

9th - 12th Grade

34 questions

7.4 Review Cubic and Cube Root Functions

Quiz

•

10th - 12th Grade

21 questions

Geometry Chapter 2 Review

Quiz

•

9th - 12th Grade

9 questions

Identifying Parts Of An Expression

Quiz

•

6th - 12th Grade

srwe

164 questions

What table does a router use to determine how to forward an IP packet?

What action will a router take on a packet with a destination IP address that is on a remote network?

Which of the following routes may be found in a routing table? (Choose all that apply.)

What is used to determine the minimum number of far-left bits that must match between the prefix in the route entry and the destination IP address.

If a router needs to send an ARP Request for the destination IPv4 address of the packet, this means the packet will be forwarded:

If a router needs to send an ARP Request for the IPv4 address in one of its route entries, this means the packet will be forwarded:

Which packet forwarding method is used by default on Cisco routers?

Which routing table principle is not correct?

Which route entry would be used for a packet with a destination IP address that matches an IP address of one of the router interfaces?

What type of network is accessed by a single route and the router has only one neighbor?

Access all questions and much more by creating a free account

Popular Resources on Wayground

Discover more resources for Mathematics