What are two benefits of implementing a traditional WAN instead of an SD-WAN solution? (Choose two.)

lower control plane abstraction

comprehensive configuration standardization

Refer to the exhibit. An engineer must configure static NAT on R1 to allow users HTTP access to the web server on TCP port 80. The web server must be reachable through ISP 1 and ISP 2. Which command set should be applied to R1 to fulfill these requirements?

ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 extendable ip nat inside source static tcp 10.1.1.100 80 209.165.201.1 80 extendable

ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 ip nat inside source static tcp 10.1.1.100 80 209. 165.201.1 80

ip nat inside source static tcp 10.1.1.100 80 209 165.200.225 80 no-alias ip nat inside source static tep. 10.1. 1.100 80 209 165.201. 1 80 no-alias

ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 ip nat inside source static tcp 10.1.1.100 8080 209.165.201.1 8080

What is a difference between Chef and other automation tools?

Chef is an agent-based tool that uses cookbooks, and Ansible is an agentless tool that uses playbooks

Chef is an agentless tool that uses playbooks, and Ansible is an agent-based tool that uses cookbooks

Chef is an agentless tool that uses a primary/minion architecture, and SaltStack is an agent-based tool that uses a primary/secondary architecture

Chef uses Domain Specific Language, and Puppet uses Ruby

An engineer is describing QoS to a client. Which two facts apply to traffic policing? (Choose two)

Policing should be performed as close to the source as possible

Policing drops traffic that exceeds the defined rate.

Policing adapts to network congestion by queuing excess traffic.

Policing should be performed as close to the destination as possible

Policing typically delays the traffic, rather than drops it

Refer to the exhibit. Cisco DNA Center has obtained the username of the client and the multiple devices that the client is using on the network. How is Cisco DNA Center getting these context details?

Those details are provided to Cisco DNA Center by the identity Services Engine

User entered those details in the Assurance app available on, 1O5 and Android devices

Cisco DNA Center pulled those details directly from the edge node where the user connected

The administrator had to assign the username to the IP address manually in the user database tool on Cisco DNA Center

How does a fabric AP fit in the network?

it is in local mode and must be connected directly to the fabric edge switch

It is in FlexConnect mode and must be connected directly to the fabric border node

It is in local mode and must be connected directly to the fabric border node

It is in FlexConnect mode and must be connected directly to the fabric edge switch

Refer to the exhibit. An engineer configures a new HSRP group. While reviewing the HSRP status, the engineer sees the logging message generated on R2: What is the cause of the message?

The same virtual IP address has been configured for two HSRP groups

A PC is on the network using the IP address 10.10.1.1

The HSRP configuration has caused a routing loop

The HSRP configuration has caused a spanning-tree loop

Refer to the exhibit. An engineer has configured an IP SLA for UDP echos. Which command is needed to start the IP SLA to test every 30 seconds and continue until stopped?

ip sla schedule 100 start-time now life forever

ip sla schedule 100 life forever

ip sla schedule 100 start-time now life 30

ip sla schedule 30 start-time now life forever

Refer to the exhibit. Cisco IOS routers R1 and R2 are interconnected using interface GiO/0. Which configuration allows R1 and R2 to form an OSPF neighborship on interface Gi0/0?

R1 (config)# router ospf 1 R1 (config-router)# no passive-interface Gi0/0

R1 (config)# router ospf 1 R1 (config-if)# network 172.20.0.0 0.0.0.255 area 1

R2(config)# router ospf 1 R2(config-router)# passive-interface G10/0

R2(config)# interface Gi0/0 R2(config-if)# ip ospf cost 1

Refer to the exhibit. A network engineer must configure the router to use the ISE-Servers group for authentication. If both ISE servers are unavailable, the local username database must be used. If no usernames are defined in the configuration, then the enable password must be the last resort to log in. Which configuration must be applied to achieve this result?

aaa authentication login default group ISE-Servers local enable

aaa authentication login default group enable local ISE-Servers

aaa authorization exec default group ISE-Servers local enable

aaa authentication login error-enable aaa authentication login default group enable local ISE-Server

Refer to the exhibit What does the Python code accomplish?

It configures interface e1/32 to be in an admin down state

It configures interface e1/32 to be in an err disable state

It returns data in JSON-RPC format

It generates a status code of 403 because the type is incorrect

Refer to the exhibit. Two indirectly connected routers fail to form an OSPF neighborship. What is the cause of the issue?

failing hello packets between the two routers

What is a characteristic of an AP operating in FlexConnect mode?

Forwarding for locally switched traffic continues when the AP loses connectivity to the WLC

FlexConnect enables an AP to connect to multiple WLCs

Al traffic traverses the WLC to ensure policy enforcement on client traffic

APs connect in a mesh topology and elect a root AP

What is a VPN in a Cisco SD-WAN deployment?

virtualized environment that provides traffic isolation and segmentation in the SD-WAN fabric

common exchange point between two different services

virtual channe/used to carry control plane information

attribute to identify a set of services offered in specific places in the SD-WAN fabric

What is the purpose of an integration API in Cisco DNA Center?

Allow the platform into approval chains in ITSM.

Enable external systems to take actions in response to an event

Enable discovery and control of the network by using HTTPS verbs

Obtain information about clients, sites, and topology from Cisco DNA Center

Refer to the exhibit Which configuration is required to summarize the Area 2 networks that are advertised to Area 0?

RouterB(config)# router ospf 1 RouterB(config-router)# area 2 range 192.168.36.0 255.255.252.0

RouterB(config)# router ospf 1 RouterB(config-router)# area 2 range 192.168.36.0 255.255.255.0

RouterB(config)# router ospf 1 RouterB(config-router)# network 192.168.38.0 255.255.255.0

RouterB(config)# router ospf 1 RouterB(config-router# network 192.168.38.0 255.255.252.0

When firewall capabilities are considered, which feature is found only in Cisco next-generation firewalls?

active/standby high availability

What is a characteristic of a Type 2 hypervisor?

It is installed on an operating system and supports other operating systems

It is completely independent of the operating system

It eliminates the need for an underlying operating system

Its main task is to manage hardware resources between different operating systems

Which function is performed by Smart in the Cisco SD-WAN architecture?

aggregation and distribution of VPN routing information

redistribution between OMP and other routing protocols

facilitation of NAT detection and traversal

execution of localized policies

Refer to the exhibit. An engineer configures HSRP and enters the show standby command. Which two facts about the network environment are derived from the output? (Choose two.)

The virtual IP address of the HSRP group is 10.1.1.1

If a router with a higher IP address and same HSRP priority as the active router becomes available, that router becomes the new active router 5 seconds later

The hello and hold timers are set to custom values

If the local device fails to receive a hello from the active router for more than 5 seconds, it becomes the active router

The local device has a higher priority setting than the active router

Refer to the exhibit. Which Python code parses the response and prints "18:32:21.474 UTC Sun Mar 10 2019"?

print(response[‘result'][‘body’][‘simple _time’])

print(response['jsonrpc'][‘body']['simple _time'])

print(response|"result'][0][‘simple_time'])

print(response|’body']['simple_time’])

Refer to the exhibit. An engineer deploys a script to retrieve the running configuration from a NETCONF-capable Cisco IOS XE device that is configured with default settings. The script falls. Which configuration must be applied to retrieve the configuration using NETCONF?

print (netconf_host.get _config("show running"))

device_params=(name':ios-xe’))

Refer to the exhibit. Which configuration change will force BR2 to reach 209. 165.201.0/27 via BR1?

Set the MED to 1 on PE2 toward BR2 outbound

Set the weight attribute to 65,535 on BR1 toward PE1

Set the local preference to 150 on PE1 toward BR1 outbound

Set the origin to igp on BR2 toward PE2 inbound

Refer to the exhibit. An engineer must modify the existing configuration so that R2 can take over as the primary router when serial interface 0/0.1 on R1 goes down. Which command must the engineer apply?

R2# track 26 interface Serial0/0.1 line-protocol

R2# standby 100 track 26 decrement 10

An engineer must use flexible NetFlow on a group of switches. To prevent overloading of the flow collector, if the flow is idle for 20 seconds, the flow sample should be exported. Which command set should be applied?

flow monitor monitorflow exporter flowexport record recordflow cache timeout active 120 cache timeout inactive 20 cache type immediate

flow record recordflow exporter flowexport record recordflow cache timeout active 120 cache timeout inactive 20 cache type immediate

flow record recordflow match ipv6 destination ip-address match ipv6 source ip-address match ipv6 protocol-type view match interface input match interface output match transport destination-port collect counter bytes long

flow monitor monitorflow exporter recordflow cache timeout active 20 cache timeout inactive 120 cache type permanent

An engineer must configure flexible NetFlow on a router. There is a requirement to view IPv4 traffic that could be marked with more than 10 separate QoS classification markings. The maximum information about the traffic flow should also be visible in the NetFlow output to detail what traffic is flowing through the network. Which flow record is suitable for the configuration?

flow record CCNA_NETFLOW match ipv4 dscp match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port

flow record CCNA_NETFLOW match ipv4 tos match ipv4 protocol match ipv4 source address match ipv4 destination address match transport source-port match transport destination-port

flow record CCNA_NETFLOW match ipv4 dscp match ipv4 protocol match ipv4 source address match ipv4 destination address

flow record CCNA_NETFLOW match ipv4 tos match ipv4 protocol match ipv4 source address match ipv4 destination address

What does the Cisco DNA Center Authentication API provide?

access token to make calls to Cisco DNA Center

list of global issues that are logged in Cisco DNA Center

Refer to the exhibit. An administrator must enable RESTCONF access to a router. Which two commands or command sets must be added to the existing configuration? (Choose two.)

aaa authentication login default local aaa authorization exec default local

Which security feature does stateless authentication and authorization use for REST API calls?

cookie-based session authentication

An engineer must configure a router to allow users to run specific configuration commands by validating the user against the router database. Which configuration must be applied?

aaa authorization exec default local

aaa authentication exec default local

aaa authorization network default local

aaa authentication network default local

What are two characteristics of VXLAN? (Choose two.)

It uses VTEPs to encapsulate and decapsulate frames

It allows for up to 16 million VXLAN segments

It extends Layer 2 and Layer 3 overlay networks over a Layer 2 underlay

It lacks support for host mobility

It has a 12-bit network identifier

What is the API keys option for REST API authentication?

a credential that is transmitted unencrypted

a username that is stored in the local router database

a predetermined string that is passed from client to server

Refer to the exhibit. What is the effect of this configuration?

The device will authenticate all users connecting to vty lines O through 4 against TACACS+

The device will allow only users at 192.168.0 202 to connect to vty lines 0 through 4

When users attempt to connect to vty lines O through 4, the device will authenticate them against TACACS+ if local authentication fails

The device will allow users at 192.168.0.202 to connect to vty lines 0 through 4 using the password ciscotestkey

Refer to the exhibit. What are two effects of this configuration? (Choose two.)

If R1 goes down, R2 becomes active and remains the active device when R1 comes back online

If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online

If R1 goes down, R2 becomes active but reverts to standby when R1 comes back online

Test 401-500

Authored by H C

Other

University - Professional Development

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

100 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Refer to the exhibit. What step resolves the authentication issue?

target 192.168.100.82 in the URI

restart the vsmart host

change the port to 12446

use basic authentication

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is a Type 2 hypervisor?

also referred to as a bare metal hypervisor because it sits directly on the physical server

installed as an application on an already installed operating system

runs directly on a physical server and includes its own operating system

supports over-allocation of physical resources

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is a characteristic of Cisco DNA southbound APls?

utilizes REST API

implements monitoring by using the SOAP protocol

enables orchestration and automation of network devices based on intent

simplifies management of network devices

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Refer to the exhibit. Which command is required on router R1 to start receiving RESTCONF requests?

R1(config)# ip http access-class 12

R1(config)# ip http server

R1(config)# restconf

R1(config)# ip http accounting commands 12 default

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Refer to the exhibit. An engineer must configure a SPAN session. What is the effect of the configuration?

Traffic received on VLANs 10 and 12 only is copied and sent to interface g0/1

Traffic sent on VLANs 10 and 12 only is copied and sent to interface g0/1

Traffic sent on VLANs 10, 11, and 12 is copied and sent to interface g0/1

Traffic received on VLANs 10,11, and 12 is copied and sent to interface g0/1

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What are the main components of Cisco TrustSec?

Cisco ASA and Cisco Firepower Threat Defense

Cisco ISE and TACACS+

Cisco ISE and Enterprise Directory Services

Cisco ISE, network switches, firewalls, and routers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

How is Auth framework used in REST API?

as a framework to hash the security information in the REST URL

by providing the external application a token that authorizes access to the account

by providing the user credentials to the external application

as a framework to hide the security information in the REST URL

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

100 questions

Tin Học ứng dụng

Quiz

•

University

100 questions

Free Mock Test 1 By Todays Ayurveda NTET Preperations

Quiz

•

University

100 questions

EMS103 CHAP 21-25

Quiz

•

Professional Development

100 questions

RIPASSO QUARTA LEZIONE

Quiz

•

University

100 questions

Engineering Management Quiz

Quiz

•

University

100 questions

AP French Assessment 2.28

Quiz

•

9th Grade - University

100 questions

PFRC 901-1000

Quiz

•

Professional Development

100 questions

IJCAHPO: COA QUICK STUDY CARDS (101-200)

Quiz

•

University

Popular Resources on Wayground

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

29 questions

Alg. 1 Section 5.1 Coordinate Plane

Quiz

•

9th Grade

$fractions$

22 questions

fractions

Quiz

•

3rd Grade

11 questions

FOREST Effective communication

Lesson

•

20 questions

Main Idea and Details

Quiz

•

5th Grade

20 questions

Context Clues

Quiz

•

6th Grade

Discover more resources for Other

15 questions

LOTE_SPN2 5WEEK3 Day 2 Itinerary

Quiz

•

Professional Development

20 questions

Black History Month Trivia Game #1

Quiz

•

Professional Development

12 questions

IREAD Week 4 - Review

Quiz

•

3rd Grade - University

20 questions

90s Cartoons

Quiz

•

Professional Development

7 questions

Fragments, Run-ons, and Complete Sentences

Interactive video

•

4th Grade - University

7 questions

Renewable and Nonrenewable Resources

Interactive video

•

4th Grade - University

10 questions

DNA Structure and Replication: Crash Course Biology

Interactive video

•

11th Grade - University

5 questions

Inherited and Acquired Traits of Animals

Interactive video

•

4th Grade - University

Test 401-500

Refer to the exhibit. What step resolves the authentication issue?

What is a Type 2 hypervisor?

What is a characteristic of Cisco DNA southbound APls?

Refer to the exhibit. Which command is required on router R1 to start receiving RESTCONF requests?

Refer to the exhibit. An engineer must configure a SPAN session. What is the effect of the configuration?

What are the main components of Cisco TrustSec?

How is Auth framework used in REST API?

What are two benefits of implementing a traditional WAN instead of an SD-WAN solution? (Choose two.)

Refer to the exhibit. An engineer must configure static NAT on R1 to allow users HTTP access to the web server on TCP port 80. The web server must be reachable through ISP 1 and ISP 2. Which command set should be applied to R1 to fulfill these requirements?

Which element enables communication between guest VMs within a virtualized environment?

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Other