If ARP=reply-only is configured on an interface, this interface will this interface do

accept all IP addresses listed in '/ip arp' as static entries

accept IP and MAC address combinations listed in '/ip arp' list

add new IP addresses in '/ip arp' list

accept all MAC-addresses listed in '/ip arp' as static entries

add new MAC addresses in '/ip arp' list

A wireless interface 'wlan1' is added to a bridge interface 'br-lan'. To enable dhcp-server for wireless interface 'wlan1', on which interface should dhcp-server be configured?

The dhcp-server cannot be enabled neither on 'wlan1', nor on 'br-lan'

To make the masquerading of the network 192.168.0.0/24, configured on the interface ether1, you should add rule

/ip firewall nat add chain=srcnat out-interface=ether1 src-address=192.168.0.0/24 action=masquerade

/ip firewall nat add chain=srcnat src-address=192.168.0.0/24 action=masquerade

/ip firewall nat add chain=dstnat in-interface=ether1 src-address=192.168.0.0/24 action=masquerade

/ip firewall nat add chain=srcnat src-address=192.168.1.0/24 action=masquerade

What is necessary for PPPoE client configuration?

Interface (on which PPPoE client is going to work)

ip firewall nat masquerade rule

Wireless interface configured as an access point

Static IP address on PPPoE client interface

The 'check-gateway' option is enabled for one route. Select all statements that are true:

In case of failure of the gateway, routes pointing to that gateway will become inactive

Gateway is checked every 10 seconds and after 2 failures, the gateway is considered unreacheable

Gateway is checked every 10 seconds and after a single failure, the gateway is considered unreacheable

Check gateway option can be configured for Ping, ARP and RARP (reverse ARP)

Choose the correct PCQ argument values to allow 256kbps maximum download and upload for each client:

kind=pcq pcq-rate=256000 pcq-classifier=dst-address

kind=pcq pcq-rate=256000 pcq-classifier=src-address

kind=pcq pcq-rate=5000000 pcq-classifier=dst-address

kind=pcq pcq-rate=5000000 pcq-classifier=src-address

kind=pcq pcq-rate=1256000 pcq-classifier=dst-address

If a packet comes to a router and starts a new, previously unseen connection, which connection state would be applied to it?

no connection state would be applied to such packet

Select statements that are true regarding the following command:/ip route add dst-address=172.16.4.0/24 gateway=192.168.4.2

The subnet mask for the destination network is 255.255.255.0

The command is used to establish a static route

The command is used to configure the default route

The default administrative distance of 100 is used

It is required to set up a web server residing on a private subnet in a LAN to be accessible from the public Internet. The web server is directly connected to a router which is facing the public Internet. Only the web server port should be accessible from the public. Which of the following configuration steps must be met (select all that apply):

A route between the router and the web server must exist

In IP firewall NAT there should be a dst-nat rule between the public IP address of the web server and the private IP of the web server

The public IP address of the web server must be installed on the router

Connection tracking must be enabled on the router

The private IP address of the web server should be routable on the Internet

There are two routes in the routing table:0 dst-addr=10.1.1.0/24 gateway=5.5.5.51 dst-addr=10.1.1.4/30 gateway=5.6.6.6Which gateway will be used to get to the IP address 10.1.1.6?

the required route is not in the routing table

both - half of the traffic will be routed through one gateway, half through the other

Router has wireless and ethernet client interfaces, all client interfaces are bridged. To create a DHCP service for all clients, DHCP server must be configured on:

Ethernet and wireless interfaces

DHCP service is not possible in this setup

What kind of packet is marked by connection-state=established matcher?

Packet is related to, but not part of an existing connection

Packet does not correspond to any known connection

Packet belongs to an existing connection, for example a reply packet or a packet which belongs to already replied connection

Packet begins a new TCP connection

Which of the following would prevent unknown clients from connecting to your AP? Choose the BEST answer.

Check the 'Do not permit unknown client' box in the wireless configuration

Configure the radius server under '/radius'

Add each known client's MAC address to your access-list configuration is the only step needed

Uncheck 'Default Authenticate' in the wireless card configuration, and add each known client's MAC address to your access-list configuration ensuring that you enable 'authenticate' in the entry

Uncheck 'Default Authenticate' in the wireless card configuration, and add each known client's MAC address to your connect-list configuration

What does the firewall action "Redirect" do? Select all true statements.

Redirects a packet to a specified port on the router

Redirects a packet to the router

Redirects a packet to a specified IP

Redirects a packet to a specified port on a host in the network

If ARP=reply-only is configured on an interface, this interface will

accept all IP addresses listed in '/ip arp' as static entries

accept IP and MAC address combinations listed in '/ip arp' list

accept all MAC-addresses listed in '/ip arp' as static entries

add new IP addresses in '/ip arp' list

add new MAC addresses in '/ip arp' list

What is necessary for PPPoE client configuration?

Interface (on which PPPoE client is going to work)

Wireless interface configured as an access point

ip firewall nat masquerade rule

Static IP address on PPPoE client interface

Uji Coba MTCNA

Authored by Siti Hidayati

Computers

12th Grade

Used 40+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

50 questions

Show all answers

MULTIPLE CHOICE QUESTION

2 mins • 2 pts

Which facility should be used, to ensure that clients with radio signal strength poorer than -90 dBm can not connect to interface wlan1 on a MikroTik AP? Choose one answer:

Registration table

Access list

Connect list

Security profiles

MULTIPLE SELECT QUESTION

2 mins • 2 pts

Consider the following diagram. Assuming that all the necessary configuration has already been done on R2 (proxy-arp is disabled), to communicate from a device on LAN1 to a device on LAN2, which of the following configurations on R1 would enable this?

/ip route add dst-address=0.0.0.0/0 gateway=192.168.99.2

/ip route add dst-address=192.168.1.0/24 gateway=192.168.99.2

/ip route add dst-address=0.0.0.0/0 gateway=Ether1

/ip route add dst-address=192.168.1.0/24 src-address=192.168.0.0/24 gateway=192.168.99.2

/ip route add dst-address=192.168.0.0/24 gateway=192.168.0.1

MULTIPLE CHOICE QUESTION

2 mins • 2 pts

A RouterBOARD clock is configured in '/system clock'. The clock resets to default after each reboot.
Select the best solution for the problem.

Configure '/system ntp client' and set a valid and reachable NTP server address

Configure '/system ntp server' and set a valid and reachable NTP client address

Open the router and ensure the CMOS battery is fine

Write a script in '/system script' to set the clock

MULTIPLE CHOICE QUESTION

2 mins • 2 pts

What is the default protocol/port of (secure) winbox?

TCP/8080

TCP/8291

TCP/22

UDP/5678

MULTIPLE CHOICE QUESTION

2 mins • 2 pts

What can be used as "Target" in the simple queue?
Note: The 'client' is the one accessing the resources, the 'server' is the one providing.

Client MAC address

Address list name

Client IP address

Server IP address

MULTIPLE CHOICE QUESTION

2 mins • 2 pts

Is action=masquerade allowed in chain=dstnat?

yes

yes, but only if dst-addr is specified

yes, but it works only for incoming connections

MULTIPLE CHOICE QUESTION

2 mins • 2 pts

MikroTik RouterOS commands can be run once a day by:

/system scheduler

/system cron

/system watchdog

/system log

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Classlink

Continue with Clever

or continue with

Microsoft

Apple

Others

Already have an account?

Similar Resources on Wayground

50 questions

HTML,CSS

Quiz

•

3rd Grade - University

51 questions

ÔN TẬP GIỮA HỌC KỲ II - LỚP 11

Quiz

•

12th Grade

50 questions

Bộ ôn 2 - Tháng 7.2023

Quiz

•

12th Grade

50 questions

TIN HỌC 10 HK2

Quiz

•

10th - 12th Grade

50 questions

Empowerment Technology

Quiz

•

12th Grade

50 questions

jaringan wifi

Quiz

•

12th Grade

55 questions

AIJ Firewall Proxy Mikrotik - PAS

Quiz

•

12th Grade

50 questions

General Review Grade 8

Quiz

•

7th - 12th Grade

Popular Resources on Wayground

8 questions

Spartan Way - Classroom Responsible

Quiz

•

9th - 12th Grade

15 questions

Fractions on a Number Line

Quiz

•

3rd Grade

14 questions

Boundaries & Healthy Relationships

Lesson

•

6th - 8th Grade

20 questions

Equivalent Fractions

Quiz

•

3rd Grade

3 questions

Integrity and Your Health

Lesson

•

6th - 8th Grade

25 questions

Multiplication Facts

Quiz

•

5th Grade

9 questions

FOREST Perception

Lesson

•

20 questions

Main Idea and Details

Quiz

•

5th Grade

Discover more resources for Computers

10 questions

Exponent Rules

Quiz

•

9th - 12th Grade

Uji Coba MTCNA

Which facility should be used, to ensure that clients with radio signal strength poorer than -90 dBm can not connect to interface wlan1 on a MikroTik AP? Choose one answer:

Consider the following diagram. Assuming that all the necessary configuration has already been done on R2 (proxy-arp is disabled), to communicate from a device on LAN1 to a device on LAN2, which of the following configurations on R1 would enable this?

A RouterBOARD clock is configured in '/system clock'. The clock resets to default after each reboot.
Select the best solution for the problem.

What is the default protocol/port of (secure) winbox?

What can be used as "Target" in the simple queue?
Note: The 'client' is the one accessing the resources, the 'server' is the one providing.

Is action=masquerade allowed in chain=dstnat?

MikroTik RouterOS commands can be run once a day by:

If ARP=reply-only is configured on an interface, this interface will this interface do

Which firewall chain you should use to filter SSH access to the router itself?

Select minimal set of software packages in RouteOS required to configuring a wireless AP

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers

Uji Coba MTCNA

Which facility should be used, to ensure that clients with radio signal strength poorer than -90 dBm can not connect to interface wlan1 on a MikroTik AP? Choose one answer:

Consider the following diagram. Assuming that all the necessary configuration has already been done on R2 (proxy-arp is disabled), to communicate from a device on LAN1 to a device on LAN2, which of the following configurations on R1 would enable this?

A RouterBOARD clock is configured in '/system clock'. The clock resets to default after each reboot.Select the best solution for the problem.

What is the default protocol/port of (secure) winbox?

What can be used as "Target" in the simple queue?Note: The 'client' is the one accessing the resources, the 'server' is the one providing.

Is action=masquerade allowed in chain=dstnat?

MikroTik RouterOS commands can be run once a day by:

If ARP=reply-only is configured on an interface, this interface will this interface do

Which firewall chain you should use to filter SSH access to the router itself?

Select minimal set of software packages in RouteOS required to configuring a wireless AP

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground

Discover more resources for Computers

A RouterBOARD clock is configured in '/system clock'. The clock resets to default after each reboot.
Select the best solution for the problem.

What can be used as "Target" in the simple queue?
Note: The 'client' is the one accessing the resources, the 'server' is the one providing.